|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Order this document by MC12095/D 2.5 GHz Low Power Prescaler With Stand-By Mode The MC12095 is a single modulus prescaler for low power frequency division of a 2.5 GHz high frequency input signal. Motorola's advanced MOSAICTM V technology is utilized to acheive low power dissipation of 24 mW at a minimum supply voltage of 2.7 V. On-chip output termination provides output current to drive a 2.0 pF (typical) high impedance load. If additional drive is required for the prescaler output, an external resistor can be added in parallel from the OUT pin to GND to increase the output power. Care must be taken not to exceed the maximum allowable current through the output. Divide ratio control input (SW) selects the required divide ratio of /2 or /4. Stand-By mode is available to reduce current drain to 100A typical when the standby pin SB is switched LOW disabling the prescaler. MC12095 MECL PLL COMPONENTS /2, /4 LOW POWER PRESCALER WITH STAND-BY MODE SEMICONDUCTOR TECHNICAL DATA * * * * * 8 2.5 GHz Toggle Frequency Supply Voltage 2.7 V to 5.5 Vdc Low Power 8.7 mA Typical Operating Temperature -40 to 85C Divide by 2 or 4 Selected by the SW Pin 1 D SUFFIX PLASTIC PACKAGE CASE 751 (SO-8) NOTE: For applications up to 1.1 GHz, please consult the MC12093 datasheet. 8 MOSAIC V is a trademark of Motorola 1 FUNCTIONAL TABLE SW H L NOTES: 1. SW: H = (VCC - 0.4 V) to VCC; L = OPEN 2. SB: H = 2.0 V to VCC; L = GND to 0.8 V Divide Ratio 2 4 SD SUFFIX PLASTIC PACKAGE CASE 940 (SSOP-8) PIN CONNECTIONS AC Test Circuit IN VCC NC OUT 1 2 3 4 8 7 6 5 VCC = 2.7 to 5.5 V C3 C1 IN 50 C2 VCC SB SW IN GND C4 Device MC12095D MC12095SD OUT EXTERNAL COMPONENTS C1 = C2 = 1000 pF C3 = 0.1 F C4 = 2.0 pF IN SB SW Gnd (Top View) ORDERING INFORMATION Operating Temp Range TA = - 40 to +85C Package SO-8 SSOP-8 (c) Motorola, Inc. 1997 Rev 3 MC12095 MAXIMUM RATINGS Parameter Power Supply Voltage, Pin 2 Operating Temperature Range Storage Temperature Range Maximum Output Current, Pin 4 NOTE: ESD data available upon request. Symbol VCC TA Tstg IO Value -0.5 to 6.0 -40 to 85 -65 to 150 8.0 Unit Vdc C C mA ELECTRICAL CHARACTERISTICS (VCC = 2.7 to 5.5 V; TA = -40 to 85C, unless otherwise noted.) Parameter Toggle Frequency (Sine Wave) Supply Current Stand-By Current Stand-By Input HIGH (SB) Stand-By Input LOW (SB) Divide Ratio Control Input HIGH (SW) Divide Ratio Control Input LOW (SW) Output Voltage Swing (2pF Load) 500-1000 MHz Input 1000-1500 MHz Input 1500-2500 MHz Input Symbol ft ICC ISB VIH1 VIL1 VIH2 VIL2 VOUT Min 500 - - 2.0 GND VCC - 0.4 OPEN 800 400 200 200 Typ 3.0 8.7 100 - - VCC OPEN - 450 250 - Max 2.5 14 200 VCC + 0.5 V 0.8 VCC + 0.5 V OPEN - - - 1000 mVpp Unit GHz mA A V V V Input Voltage Sensitivity VIN mVpp Figure 1. Typical Minimum Input Sensitivity versus Input Frequency 0 -10 Input Power Level (dBm) -20 -30 -40 500 700 900 1100 1300 1500 1700 1900 2100 2300 2500 Input Frequency (MHz) (Divide By 2 Mode, T = 25C, VCC = 2.7 V) 2 MOTOROLA RF/IF DEVICE DATA MC12095 Figure 2. Typical Output Amplitude versus Frequency over Temperature 1800 1600 1400 Output Amplitude (mVpp) 1200 1000 800 SPEC 600 400 200 0 500 -40C +25C +85C 750 1000 1250 1500 1750 2000 2250 2500 Input Frequency (MHz) (Divide By 2 Mode, VCC = 2.7 V) Figure 3. Typical Output Amplitude versus Frequency over Temperature 1800 1600 1400 Output Amplitude (mVpp) 1200 1000 800 SPEC 600 400 200 0 500 -40C +25C +85C 750 1000 1250 1500 1750 2000 2250 2500 Input Frequency (MHz) (Divide By 4 Mode, VCC = 2.7 V) MOTOROLA RF/IF DEVICE DATA 3 MC12095 Figure 4. Input Impedance versus Frequency 150 125 100 R (Ohms) 75 50 25 0 500 700 900 1100 1300 1500 1700 1900 2100 2300 2500 Input Frequency (MHz) Figure 5. Input Impedance versus Frequency 100 50 0 jX (Ohms) -50 -100 -150 -200 500 700 900 1100 1300 1500 1700 1900 2100 2300 2500 Input Frequency (MHz) 4 MOTOROLA RF/IF DEVICE DATA MC12095 OUTLINE DIMENSIONS D SUFFIX PLASTIC PACKAGE CASE 751-06 (SO-8) ISSUE T C 5 A 8 D E 1 4 H 0.25 M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETER. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ h B C e A SEATING PLANE X 45 _ q L 0.10 A1 B 0.25 M CB S A S q SD SUFFIX PLASTIC PACKAGE CASE 940-03 (SSOP-8) ISSUE B 8X K REF 0.12 (0.005) 0.25 (0.010) M TU S V S N M N L/2 L PIN 1 IDENT 1 8 5 B 4 F DETAIL E K J 0.20 (0.008) M TU S 0.076 (0.003) -T- SEATING PLANE C D G H DETAIL E MOTOROLA RF/IF DEVICE DATA EEEE CCCC EEEE CCCC K1 SECTION N-N A -V- -U- J1 NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 5 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION/INTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF K DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR INTRUSION SHALL NOT REDUCE DIMENSION K BY MORE THAN 0.07 (0.002) AT LEAST MATERIAL CONDITION. 6 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 2.87 3.13 5.20 5.38 1.73 1.99 0.05 0.21 0.63 0.95 0.65 BSC 0.44 0.60 0.09 0.20 0.09 0.16 0.25 0.38 0.25 0.33 7.65 7.90 0_ 8_ INCHES MIN MAX 0.113 0.123 0.205 0.212 0.068 0.078 0.002 0.008 0.024 0.037 0.026 BSC 0.017 0.023 0.003 0.008 0.003 0.006 0.010 0.015 0.010 0.013 0.301 0.311 0_ 8_ -W- 5 MC12095 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 Customer Focus Center: 1-800-521-6274 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 - http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141, 4-32-1 Nishi-Gotanda, Shagawa-ku, Tokyo, Japan. 03-5487-8488 6 MC12095/D MOTOROLA RF/IF DEVICE DATA |
Price & Availability of MC12095D |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |